How to Choose the Correct Size Evaporative Cooler for Your Home
Choosing the right size evaporative cooler starts with understanding how much air your home needs the system to move. For ducted evaporative cooling, size is usually based on airflow, commonly measured in litres per second, rather than room area alone. A small home with standard ceilings may need far less airflow than a large open-plan house with high ceilings, long duct runs and multiple living zones.
The right unit needs to deliver enough fresh, cooled air to the spaces you use most, while allowing that air to move through the home and escape through open windows or doors. If the cooler is too small, rooms can feel warm, stuffy or unevenly cooled. If it is too large, it may be noisy, drafty and more expensive than necessary.
This guide explains how to estimate the evaporative cooler size your home may need, what affects the final recommendation, and why airflow and duct design matter just as much as the unit itself.
Table of Contents
- How to Work Out What Size Evaporative Cooler Your Home Needs
- Example Sizing Guide
- Use Our Calculator to Estimate an Evaporative Cooling Size
- Want to work it out yourself? Here is a step by step guide
- What Can Impact Sizing Evaporative Cooling for Melbourne Homes
- Common Sizing Mistakes to Avoid
- Why a Bigger Evaporative Cooler Isn’t Always Better
- Choosing Between Evaporative Cooling Brands and Models
- How Much Does Evaporative Cooling Cost in Melbourne?
- Considering an Evaporative Cooling Upgrade or New Installation? Get in touch with ExtrordinAir today
How to Work Out What Size Evaporative Cooler Your Home Needs
For a ducted evaporative cooler, size is usually based on airflow.
In Australia, ducted evaporative cooling capacity is commonly discussed in:
- Litres per second, written as L/s
- Cubic metres per hour, written as m³/h
- Air changes per hour, written as ACH
As a general rule, size evaporative cooling around 30 air changes per hour for the area being cooled.
A simple starting point is:
Room or home volume × 30 ACH = required airflow in m³/h
Then convert to L/s:
m³/h ÷ 3.6 = L/s
For example, a 160 m² home with 2.4 m ceilings has a volume of 384 cubic metres. (160 × 2.4 = 384 m³)
At 30 air changes per hour:
384 × 30 = 11,520 m³/h
Converted to L/s:
11,520 ÷ 3.6 = 3,200 L/s
So, as a rough starting point, that home may need an evaporative cooler capable of delivering around 3,200 L/s of airflow, before considering duct layout, ceiling height, room usage, insulation, outlet placement and the specific model’s installed performance.
Example Sizing Guide
These examples use 30 ACH and a ceiling height of 2.4 m.
| Area being cooled | Volume | Airflow at 30 ACH | Approx. L/s |
|---|---|---|---|
| 80 m² | 192 m³ | 5,760 m³/h | 1,600 L/s |
| 120 m² | 288 m³ | 8,640 m³/h | 2,400 L/s |
| 160 m² | 384 m³ | 11,520 m³/h | 3,200 L/s |
| 200 m² | 480 m³ | 14,400 m³/h | 4,000 L/s |
| 240 m² | 576 m³ | 17,280 m³/h | 4,800 L/s |
These figures are a guide only. The right unit may change depending on the home layout, number of outlets, duct runs, insulation, sun exposure, open-plan areas and how the household uses the system.

Image Reference: Airah.org.au
Use Our Calculator to Estimate an Evaporative Cooling Size
Not sure what size evaporative cooler your home may need? Use the calculator below to estimate the airflow required for the area you want to cool. The result is a guide only, but it gives you a useful starting point before comparing models or booking an installer.
Evaporative cooler size calculator
Enter the area you want to cool and your ceiling height to estimate the airflow your ducted evaporative cooler may need.
Your estimated evaporative cooling airflow
Want to work it out yourself? Here is a step by step guide
1. Work out the area you want to cool
Start with the rooms or zones you expect the system to cool most of the time.
For a whole-home ducted evaporative system, this may be the total floor area. For some homes, it may be more realistic to focus on living areas and bedrooms rather than rarely used rooms.
Measure the floor area in square metres:
Length × width = area in m²
If you are sizing for the whole house, use the approximate internal floor area, not the block size.
2. Multiply by ceiling height
Evaporative cooling is sized by air volume, not just floor area.
Use:
Area × ceiling height = volume in m³
Example:
A 45 m² open-plan living area with 2.7 m ceilings:
45 × 2.7 = 121.5 m³
Higher ceilings increase the air volume, so a home with 2.7 m or 3 m ceilings will need more airflow than a similar floor plan with standard 2.4 m ceilings.
3. Apply an air-change rate
For a practical first estimate, use 30 ACH.
Example:
121.5 m³ × 30 ACH = 3,645 m³/h
4. Convert m³/h to L/s
Most Australian evaporative cooler specifications are easier to compare in L/s.
Use:
m³/h ÷ 3.6 = L/s
Example:
3,645 ÷ 3.6 = 1,012.5 L/s
So that living area would need roughly 1,000 L/s as a starting airflow estimate.
5. Compare that with model airflow ratings
Once you have an airflow estimate, compare it with suitable evaporative cooler models.
Keep in mind that a model’s rated airflow may not be exactly what you experience inside the home. Installed performance can be affected by duct length, number of outlets, roof space constraints, bends, outlet positions and how the system is commissioned.
That is why a site inspection is still important. The calculation gives you a starting point, but it does not replace a professional system design. Please get in touch with our team for a quote.
What Can Impact Sizing Evaporative Cooling for Melbourne Homes
1. Melbourne weather and humidity
Evaporative cooling performs best in hot, dry conditions. In Melbourne, many summer days suit evaporative cooling well, especially when humidity is lower.
However, performance can drop on humid days. If you want consistent temperature control during humid weather, or you prefer to keep all windows and doors closed, you may want to compare evaporative cooling with refrigerated air conditioning before deciding. See our guide to evaporative cooling vs air conditioning in Melbourne.
2. How much of the home you want to cool
A system sized for the whole house needs more airflow than one intended mainly for living areas and bedrooms.
If your home has large open-plan spaces, high ceilings, long hallways or multiple wings, the airflow and outlet layout become especially important. A unit that looks suitable by floor area alone may still perform poorly if the air cannot move through the home properly.
3. Ceiling height
A 200 m² home with 2.4 m ceilings contains about 480 m³ of air.
A 200 m² home with 3 m ceilings contains about 600 m³ of air.
That is a 25% increase in volume, which means the system needs more airflow to achieve the same number of air changes per hour.
4. Insulation, shading and heat gain
Evaporative cooling replaces indoor air with cooled fresh air, but the home still needs help resisting heat.
Good insulation, external shading, curtains, blinds and draught management can reduce how hard the evaporative air conditioner needs to work. A poorly insulated home with large west-facing windows may need more airflow than a well-shaded, insulated home of the same size.
5. Duct and outlet design
Ducted evaporative cooling relies on moving large volumes of air. The ductwork must be designed to support that airflow.
Important design details include:
- Number of outlets
- Outlet size
- Duct diameter
- Duct length
- Number of bends
- Roof space access
- Outlet placement in rooms
- Air path to open windows or relief points
A correctly sized unit connected to poor ductwork can still feel weak. Similarly, oversized equipment will not fix badly placed outlets or restricted ducts.
6. Window and door operation
This is one of the biggest differences between evaporative and refrigerated cooling.
With evaporative cooling, you should not seal the home while the cooler is running. Some windows or doors need to be open so the system can push warm, moist air out and keep fresh cooled air moving through the home. As a practical rule, open windows or doors in the rooms you want cooled, or create a clear air path through those rooms. If the house feels muggy, stuffy or pressurised, you may not have enough relief airflow.
7. Water use
Evaporative coolers use water as part of the cooling process. The amount varies depending on model size, fan speed, weather, water management settings and runtime.
For a deeper Melbourne-specific guide, see our article on evaporative cooling water usage in Melbourne.
Common Sizing Mistakes to Avoid
- Sizing only by floor area: Floor area is useful, but it is not enough. Ceiling height, room volume, duct design and airflow paths all matter.
- Treating evaporative cooling like refrigerated air conditioning: Evaporative cooling needs air movement through the home. Closing every window and door can reduce performance and make the house feel humid.
- Choosing the biggest model available: An oversized system can be noisy, drafty and inefficient. Correct sizing is better than maximum sizing.
- Ignoring ductwork: The cooler, ducts and outlets need to work together. A strong rooftop unit cannot perform properly through restricted or poorly designed ductwork.
- Forgetting winter heat loss: If outlets and roof units are not sealed in winter, they can let warm air escape. This affects heating comfort and energy use outside the cooling season.
Why a Bigger Evaporative Cooler Isn’t Always Better
A larger evaporative cooler may deliver more airflow, but bigger is not automatically better. Oversizing can create problems such as:
- Too much air noise
- Drafty rooms
- Higher water use
- Higher upfront cost
- Poor control at lower fan speeds
- Ductwork that cannot handle the airflow properly
Undersizing is also a problem. An undersized unit may run at high speed more often, struggle to move enough air through the home, and leave rooms feeling warm or stagnant.
The goal is not to choose the biggest unit available. The goal is to choose the right airflow for the home and match it with good duct design.
Choosing Between Evaporative Cooling Brands and Models
Once the required airflow range is known, the next step is choosing a model and brand that suits your home, budget and expectations.
Common considerations include:
- Airflow capacity
- Pad quality and saturation efficiency
- Fan motor type
- Noise level
- Water management system
- Controller options
- Warranty
- Parts availability
- Service access
- Suitability for your roof and duct layout
If you are comparing popular Australian brands, see our guide to Bonaire vs Braemar evaporative cooling.
As a general guide, smaller homes, units or compact single-storey layouts may suit lower-capacity models such as the Brivis L36, P36 or F36D, or Bonaire options such as the Summer Breeze BBM800/BBM950 or Silhouette Premium SVS950.
Medium homes often need a step up in airflow, with models such as the Brivis L46–L56, P46–P66 or F56D, Bonaire BBM950/BBM1250, Silhouette Premium SVS1100/SVS1250, or an equivalent Braemar model commonly considered depending on the duct layout.
Larger homes, high ceilings, big open-plan living areas or long duct runs may require higher-airflow units such as the Brivis L66/L76, P76, F76D/F86DS or AD86, or premium high-capacity options from Breezair, Braemar or Bonaire.
These examples are starting points only: the final model should be selected after checking the home’s floor area, ceiling height, insulation, outlet positions, duct design, ventilation paths and roof access. Please get in touch, we’d be happy to give you a no obligation quote.
How Much Does Evaporative Cooling Cost in Melbourne?
The cost depends on the unit size, brand, roof access, ductwork, number of outlets, replacement requirements and whether you are installing a new system or replacing an old one.
Larger systems generally cost more, but the unit is only part of the total job. Ducting, outlets, controls, installation conditions and commissioning all affect the final price. If you are replacing an existing evaporative cooler, we will reuse ductwork and outlets when they are still in good condition.

Considering an Evaporative Cooling Upgrade or New Installation? Get in touch with ExtrordinAir today
If you are not sure whether evaporative cooling, refrigerated air conditioning or a replacement system is the best fit, ExtrordinAir can inspect your home, explain the options clearly, and recommend a system that suits how you use the space.
Give our Melbourne office a call on 1800 296 885 or complete your details on the form below and one of our friendly team will be in touch.



